E.F. Johnson Company 9800 Series Manuel de service Page 23
- Page / 69
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
OPERATION
2-16
Revised January 2001
Part No. 001-9800-501
• If the radio system is busy, “BUSY” is displayed
and a busy tone sounds. The call automatically
proceeds when the radio system becomes avail-
able. If the call is ended before it proceeds, your
position in queue is lost.
Answering a Telephone Call
Telephone calls are automatically received if a
SMARTNET/SmartZone channel is selected. Proceed
as follows:
1. When a telephone call is received, “ringing” similar
to a standard telephone is heard, and the display
indicates “PHONE” on the bottom line.
2. To answer the call, press the Phone option switch
and the phone mode is indicated by the icon.
Press the PTT switch to talk and release it to listen.
3. To end the call when the conversation is complete or
at any other time, press the Phone option switch
again.
2.5.7 CALL ALERT
The Call Alert
™
feature allows pages to be sent
and received as follows:
Sending a Page
1. With a SMARTNET/SmartZone channel selected,
momentarily press the Call Alert option switch. The
tag (alias) of the last ID called is displayed if it
matches an ID in your call list. Otherwise, the last
ID called is displayed.
2. To select the desired ID, rotate the Select switch to
scroll through the ID list. Press the Call Alert option
switch again to cancel the call.
3. Press the PTT switch to send the page. The display
then indicates the alias of the radio being paged.
Conditions that may then occur are as follows:
• If the radio you are paging is on the air and
received your page, a signaling success tone (six
beeps) sounds and the display momentarily indi-
cates “ACK RCVD” on the bottom line. The alias
of the selected channel is then displayed
continuously.
• If the radio you are paging is not in service, a tone
sounds and “NO ACK” is displayed. Press the Call
Alert switch again to cancel the page.
Answering a Page
1. When a page is received, “PAGE RCV” is indicated
on the bottom line and a recurring received page
tone (six beeps) sounds.
2. Answering a page is the same as placing a private
call. Therefore, press the Private Call option switch
and follow the instructions for placing a private call
in Section 2.5.4 or 2.5.5, whichever is applicable.
2.5.8 MESSAGING
The messaging feature allows preprogrammed
messages to be sent to your dispatcher. Up to 16
messages can be preprogrammed, and they are identi-
fied by alias (name). If a Message option switch is
programmed, messages are sent as follows:
1. Momentarily press the Message option switch. The
alias of the last message sent is displayed.
2. Scroll through the message list by rotating the Select
switch until you find the desired message. Press the
Message option switch again to cancel the message.
3. Press the PTT switch to send the message. When the
message is received and acknowledged by the
dispatcher, a signaling success tone (six beeps)
sounds and the display returns to the normal channel
indication. If there is no acknowledgment after 6
seconds, a tone sounds and “NO ACK” is displayed.
Press the Message option switch again to return to
normal operation.
2.5.9 SENDING STATUS CONDITIONS
The status feature allows you to send your current
status to a dispatcher. Up to eight status conditions can
be preprogrammed, and they are identified by an alias
(name). If the Status option switch is programmed,
status conditions are sent as follows:
- 800 MHZ MOBILE 1
- Service Manual Addendum 2
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (CONT’D) 4
- LIST OF FIGURES 4
- LIST OF TABLES 4
- 0 A 12345 5
- GENERAL INFORMATION 6
- 1.5.4 NPSPAC MODELS 7
- 1.5.5 PROGRAMMING 7
- 1.5.6 TRANSCEIVER ALIGNMENT 7
- 2.2.2 DISPLAY DESCRIPTION 9
- OPERATION 10
- Revised January 2001 10
- Part No. 001-9800-501 10
- 2.3.6 HOME ZONE 11
- 2.3.7 TIME-OUT TIMER 11
- 2.3.8 TONE ENABLE/DISABLE 11
- 2.3.9 POWER TURN-OFF DELAY 11
- 2.3.11 SCANNING 12
- S” icon is 12
- MONITORING 12
- S” icon or 13
- S”) is indicated in the 14
- SMARTZONE OPERATION 14
- 2.4.6 CALL GUARD SQUELCH 16
- 2.4.7 PENALTY TIMER 16
- 2.4.8 CONVERSATION TIMER 16
- 2.4.9 REPEATER TALK-AROUND 16
- 2.4.10 POWER OUTPUT SELECT 16
- S” icon is then indicated 17
- P” is indicated 17
- 2.5.2 VIEWING UNIT ID 19
- 2.5.3 STANDARD GROUP CALLS 19
- C” in the 19
- C” in the upper part of the 20
- 2.5.6 TELEPHONE CALLS 22
- 0-9, , and # keys. To 22
- 2.5.7 CALL ALERT 23
- 2.5.8 MESSAGING 23
- 2.5.11 FAILSOFT OPERATION 24
- 2.5.13 DYNAMIC REGROUPING 25
- 2.5.14 SMARTZONE FEATURES 25
- 2.6 SUPERVISORY TONES 26
- 3.1 GENERAL 27
- 3.1.1 PROGRAMMING SETUP 27
- 3.1.2 COMPUTER DESCRIPTION 27
- TRANSCEIVER 28
- 3.1.5 STARTING AND EXITING 28
- 3.1.6 PROGRAMMING FILE TYPES 28
- 3.1.7 HELP FILES 29
- 3.1.8 SCREEN GROUPS 29
- 3.1.9 DISPLAYING SCREENS 29
- PROGRAMMING 30
- Part No. 001-7780-501 30
- 3.4.1 INTRODUCTION 33
- Radio-Wide Scan List Screen 33
- Modify List Screen 34
- CHANNELS 38
- PARAMETERS 39
- SYSTEMS AND CHANNELS 40
- 3.6.1 INTRODUCTION 40
- GENERAL SCREEN 40
- OTHER ID’S SCREEN 41
- PHONE INTERCONNECT SCREEN 42
- TALK GROUPS SCREEN 42
- EMERGENCY SETTINGS SCREEN 43
- SCREEN PARAMETERS 48
- 800 MHz Channels 50
- Figure 4-1 Alignment Setup 57
- 4.1 GENERAL 57
- 4.1.1 INTRODUCTION 57
- 4.1.2 TEST SETUP 57
- • Windows 58
- • 4 megabytes of RAM 58
- • An available serial port 58
- 4.2 TRANSMIT POWER OUTPUT 59
- 4.3 FREQUENCY SET/VCO CHECK 60
- 4.4 TRANSMIT MODULATION 60
- 4.6 SQUELCH ADJUSTMENT 61
- 4.7 RSSI ADJUSTMENT 61
- 4.8 PERFORMANCE TESTING 61
- 98xx RF Board Part Change 62
- DSP Board Parts List 62
- Ref No. Description Part No 63
- Part Number 001-9800-501 69
- 1-01 hph Printed in U.S.A 69
Produits connexes et manuels pour Les radios bidirectionnelles E.F. Johnson Company 9800 Series
(27 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.664 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels