E.F. Johnson Company 9800 Series Manuel de service Page 57
- Page / 69
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4-1
Revised January 2001
Part No. 001-9800-501
ALIGNMENT AND PERFORMANCE TESTS
SECTION 4 ALIGNMENT AND PERFORMANCE TESTS
Figure 4-1 Alignment Setup
Ign Sense
Remote Programming Interface (RPI)
13.6 VDC
Power Supply
Signal Generator/
Wattmeter
50-ohm
Load
Comm. Monitor
(Optional)
Part No. 023-9800-000
PC-Compatible
Computer
4.7-ohm
Speaker Load
4.1 GENERAL
4.1.1 INTRODUCTION
The alignment procedure described in this section
should be performed if repairs are made that could
affect the factory alignment. In addition, before a
transceiver is initially placed in service, the perfor-
mance tests described in Section 4.8 should be
performed.
To perform the alignment described in this
section, special PCTune software (see Table 1-1) and
the same basic computer setup used for programming
is required. This equipment is shown above and also
described in Section 3.1. Remote Programming Inter-
face (RPI), Part No. 023-9800-000, or others can be
used (except 023-5300-000). The speaker and micro-
phone audio jacks on the 9800 RPI are not required in
this application.
With 800 MHz models, only three or four adjust-
ments are made manually and the others are made
digitally using the PCTune software. The manual
adjustments tune the IF and high power PA, and set the
TCXO frequency. If they do not need to be reset, the
transceiver can be tuned without removing the top or
bottom covers.
This transceiver does not have a special test mode
that is selected. The PCTune software automatically
selects the frequencies and other test conditions that
are required to perform the alignment. If the trans-
ceiver must be controlled manually to perform such
things as testing or troubleshooting, program tempo-
rary conventional channels.
4.1.2 TEST SETUP
Connect the test setup shown in Figure 4-1. Addi-
tional information follows on equipment in this setup.
- 800 MHZ MOBILE 1
- Service Manual Addendum 2
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (CONT’D) 4
- LIST OF FIGURES 4
- LIST OF TABLES 4
- 0 A 12345 5
- GENERAL INFORMATION 6
- 1.5.4 NPSPAC MODELS 7
- 1.5.5 PROGRAMMING 7
- 1.5.6 TRANSCEIVER ALIGNMENT 7
- 2.2.2 DISPLAY DESCRIPTION 9
- OPERATION 10
- Revised January 2001 10
- Part No. 001-9800-501 10
- 2.3.6 HOME ZONE 11
- 2.3.7 TIME-OUT TIMER 11
- 2.3.8 TONE ENABLE/DISABLE 11
- 2.3.9 POWER TURN-OFF DELAY 11
- 2.3.11 SCANNING 12
- S” icon is 12
- MONITORING 12
- S” icon or 13
- S”) is indicated in the 14
- SMARTZONE OPERATION 14
- 2.4.6 CALL GUARD SQUELCH 16
- 2.4.7 PENALTY TIMER 16
- 2.4.8 CONVERSATION TIMER 16
- 2.4.9 REPEATER TALK-AROUND 16
- 2.4.10 POWER OUTPUT SELECT 16
- S” icon is then indicated 17
- P” is indicated 17
- 2.5.2 VIEWING UNIT ID 19
- 2.5.3 STANDARD GROUP CALLS 19
- C” in the 19
- C” in the upper part of the 20
- 2.5.6 TELEPHONE CALLS 22
- 0-9, , and # keys. To 22
- 2.5.7 CALL ALERT 23
- 2.5.8 MESSAGING 23
- 2.5.11 FAILSOFT OPERATION 24
- 2.5.13 DYNAMIC REGROUPING 25
- 2.5.14 SMARTZONE FEATURES 25
- 2.6 SUPERVISORY TONES 26
- 3.1 GENERAL 27
- 3.1.1 PROGRAMMING SETUP 27
- 3.1.2 COMPUTER DESCRIPTION 27
- TRANSCEIVER 28
- 3.1.5 STARTING AND EXITING 28
- 3.1.6 PROGRAMMING FILE TYPES 28
- 3.1.7 HELP FILES 29
- 3.1.8 SCREEN GROUPS 29
- 3.1.9 DISPLAYING SCREENS 29
- PROGRAMMING 30
- Part No. 001-7780-501 30
- 3.4.1 INTRODUCTION 33
- Radio-Wide Scan List Screen 33
- Modify List Screen 34
- CHANNELS 38
- PARAMETERS 39
- SYSTEMS AND CHANNELS 40
- 3.6.1 INTRODUCTION 40
- GENERAL SCREEN 40
- OTHER ID’S SCREEN 41
- PHONE INTERCONNECT SCREEN 42
- TALK GROUPS SCREEN 42
- EMERGENCY SETTINGS SCREEN 43
- SCREEN PARAMETERS 48
- 800 MHz Channels 50
- Figure 4-1 Alignment Setup 57
- 4.1 GENERAL 57
- 4.1.1 INTRODUCTION 57
- 4.1.2 TEST SETUP 57
- • Windows 58
- • 4 megabytes of RAM 58
- • An available serial port 58
- 4.2 TRANSMIT POWER OUTPUT 59
- 4.3 FREQUENCY SET/VCO CHECK 60
- 4.4 TRANSMIT MODULATION 60
- 4.6 SQUELCH ADJUSTMENT 61
- 4.7 RSSI ADJUSTMENT 61
- 4.8 PERFORMANCE TESTING 61
- 98xx RF Board Part Change 62
- DSP Board Parts List 62
- Ref No. Description Part No 63
- Part Number 001-9800-501 69
- 1-01 hph Printed in U.S.A 69
Produits connexes et manuels pour Les radios bidirectionnelles E.F. Johnson Company 9800 Series
(27 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.128 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels