E.F. Johnson Company 5300 Series Instructions d'exploitation Page 113
- Page / 216
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ES Series Mobile Radio Operating Manual 5-31
Conventional Mode Features
When the desired value is displayed, store it by pressing the Select switch. A single
beep sounds when the switch is pressed (if that option is enabled).
TX TIMER - Selects the transmit time-out timer. Rotate the Select switch to
decrement/increment the timer in 15-second steps from 0-225 or disable it by selecting
0 seconds. When the desired value is displayed, store it by pressing the Select switch. A
single beep sounds when the switch is pressed (if that option is enabled).
PEN TIMER - Selects the penalty timer. Rotate the Select switch to decrement/
increment the timer in 15-second steps from 0-225 or disable it by selecting 0 seconds.
When the desired value is displayed, store it by pressing the Select switch. A single
beep sounds when the switch is pressed (if that option is enabled).
CONV TIMER - Selects the conversation timer. Rotate the Select switch to
decrement/increment the timer in 30-second steps from 0-450 or disable it by selecting
0 seconds. When the desired value is displayed, store it by pressing the Select switch.A
single beep sounds when the switch is pressed (if that option is enabled).
5.14.6 Channel Parameters
The “CHAN PARMS” menu parameter selects the following conventional channel
parameters that can be reprogrammed. Press Select switch to select the “CHAN PARMS”
parameter and then rotate that switch to display the desired parameter. Then press the
Select switch again to select it. A single beep sounds when the switch is pressed (if that
option is enabled). The squelch control parameters are unique to the type of conventional
channel selected (analog or Project 25).
Note If “PASSWORD” is briefly displayed when attempting to select a parameter, see
Section 5.14.2.
Note If a mixed mode channel is selected, both the Rx Code (analog) and Rx NAC (P25) which
follow can be programmed. In addition, if the Tx Type is Analog, a Tx Code is
programmed, and if it is Digital (P25), a Tx NAC is programmed.
RX FREQ - Programs the receive channel frequency. To select the digit to change or
move the cursor to the right, press the Select switch. Then to display the desired digit,
rotate the Select switch. The frequency is stored after programming the last digit. If an
invalid frequency is entered, a beep sounds, “INVALID” is briefly displayed, and the
frequency editing mode continues to be selected.
TX FREQ - Selects the transmit frequency the same the preceding RX FREQ.
CTCSS/DCS Squelch Control (Analog Channel) - Changes the preset squelch setting
on that channel. The default setting is “0” and values of –7 to +7 can be selected.
Increasing this setting toward +7 causes the squelch to open sooner so that weaker
signals can be received, and decreasing it toward –7 causes the opposite to occur.
RX CODE - Sets the receive Call Guard (CTCSS/DCS) code. The currently selected
code is initially displayed. If required, rotate and press the Select switch to select the
- ES Series Mobile Radio 1
- Operating Manual 1
- Table of Contents 5
- 3 General Operation 3-1 6
- 4 Radio Wide Features 4-1 7
- 7 Multi-Net Features 7-1 10
- Contents 11
- 9 Data Features 9-1 12
- 11 Service Information 11-1 12
- List of Figures 15
- List of Tables 17
- Safety Information 19
- Instructions 20
- Mobile Antennas 21
- Approved Accessories 22
- Radio Overview 23
- 1.3 Supported Software 25
- 1.4 Available Options 26
- 1.5 Licensing 27
- 1.6 Radio Accessories 27
- 1.6.2 Handheld Control Unit 28
- 1.6.3 Base Station Unit 29
- Controls & Display 31
- Programmable Option Buttons 32
- 2.1.2 Display 33
- 2.2 Lightning Control Head 36
- 2.2.1 Front Panel Controls 37
- *4-Way Navigation Pad 38
- 2.2.2 Display 39
- 2.2.3 Mobile Display Modes 40
- 2.3 Rear Panel Connectors 43
- 2.4.3 Hardware Setup 45
- 2.4.5 Dual Control Operation 47
- 2.5 External Speaker 48
- General Operation 51
- 3.1.1.1 Setting Volume Level 52
- 3.1.2 Power-Up Password 53
- 3.1.2.6 Master Password 54
- 3.1.2.7 Zone Password 54
- 3.1.6.1 Channel Lock Option 56
- 3.1.6.4 Direct Channel Select 57
- 3.1.7 Setting Squelch Control 59
- 3.1.8 Transmit Disable 60
- 3.1.12 Radio Service 61
- 3.2 Operating Modes 62
- 3.2.3 P25 Trunked Mode 63
- 3.2.4 Multi-Net Mode 64
- 3.2.5.1 Systems 65
- 3.2.5.2 Channels 66
- 3.2.5.3 Zones 66
- Radio Wide Features 67
- 4.2 Menu Mode 69
- 4.3 Time-Out Timer 70
- 4.4 Home Channel Select 70
- 4.5 Power Output Select 70
- 4.6 Alert Tone Select 71
- 4.7 Power Turn-Off Delay 71
- 4.8 Horn Alert 72
- 4.10 Surveillance Mode 73
- 4.11 Public Address 73
- 4.12 Scanning 74
- Scan Enable Indicator 75
- 4.13 Scan Lists 77
- Scan List Indicator 77
- 4.14.1 Viewing GPS Data 80
- 4.15 Over the Air Programming 81
- 4.15.2 OTAP Transfer Times 82
- 5.2 Monitor Mode 84
- 5.3 Busy Channel Lockout 85
- 5.4 Call Guard Squelch 85
- 5.4.2 Tone Call Guard Squelch 86
- 5.4.4 Disable Call Guard 87
- 5.5 Penalty Timer 88
- 5.6 Conversation Timer 89
- 5.7 Repeater Talk-Around 89
- 5.9 Emergency Alarm and Call 90
- 5.9.2 Emergency Call Alert 91
- 5.9.3 Emergency Calls 91
- 5.9.3.1 Emergency Hot Mic 92
- 5.9.5 Emergency Talkgroup 93
- 5.10.1 Selecting a Scan List 93
- Priority Indicator 95
- 5.10.4 Talkgroup Scanning 96
- 5.12 DTMF / ANI Signaling 98
- 5.12.1 Single Tone Encoder 99
- 5.12.2 Two Tone Encoder 99
- 5.12.3 Five Tone Encoder 100
- 5.12.4 MDC1200 Compatibility 100
- 5.12.5 GE Star 100
- 5.13 Project 25 Mode Features 101
- 5.13.6 P25 Group Calls 103
- 5.13.7 P25 Unit Calls 104
- 1 - 16 1 1 - 16 105
- 17 - 32 2 1 - 16 105
- 33 - 48 3 1 - 16 105
- 5.13.9 Call Alert 107
- 5.13.10 Call History 108
- 5.13.11 Messaging 108
- 5.13.12 Status Messaging 109
- 5.13.13 P25 Packet Data 109
- 5.14 Keypad Programming 110
- 5.14.2 Zone Password 111
- 5.14.3 Zone Change Parameter 112
- 5.14.5 System Parameters 112
- 5.14.6 Channel Parameters 113
- 5.15 Text Messaging 115
- Conventional Mode Features 118
- SMARTNET / SmartZone / P25 119
- Trunked Features 119
- 6.3 Standard Group Calls 120
- 6.5 Telephone Calls 125
- 6.6 Call Alert 127
- 6.6.1 Answering a Page 128
- 6.6.2 Initiating a Page 128
- 6.7 Messaging 130
- 6.8 Sending Status Conditions 130
- 6.9 Emergency Alarm and Call 131
- 6.9.2 Emergency Call Alert 132
- 6.9.3 Emergency Calls 132
- 6.10 Failsoft Operation 134
- 6.12 Dynamic Regrouping 137
- 6.13.1 Busy Override 138
- 6.13.2 Site Trunking 138
- 6.13.5 Auto Site Search 139
- 6.13.6 ZoneFail Site Lock 139
- 6.13.7 P25 Wide Area Scan 140
- 6.13.10 Radio Information 141
- Multi-Net Features 143
- 7.2 Multi-Net Features 145
- 7.2.2 Receive Priority Calls 146
- 7.2.3 Access Priority 147
- 7.2.4 System Authorization 147
- 7.3 Caller Identification 148
- 7.6 Emergency 149
- 7.7 Encryption 150
- 7.8 Group Scanning 150
- 7.8.2 Group Scan Lists 151
- 7.8.2.3 Scan List Select 152
- 7.8.3.1 Receive Delay 152
- 7.8.3.2 Call Delay 153
- 7.9 Multi-Net Group Calls 154
- 7.10 Multi-Net Special Calls 155
- CALL is 155
- 7.10.1 Placing A Special Call 156
- *, #, and 157
- 7.10.2.2 Directed Group Calls 158
- 7.12 Receive-Only Channels 161
- 7.13.1 Roaming (Site Search) 162
- 7.13.3 Automatic Site Search 162
- 7.13.5 Manual Site Search 163
- 7.14 Status Messages 164
- 7.15.1 Exiting Queue Mode 165
- 7.18 Transmit Inhibit 166
- 8.1 Encryption Algorithms 169
- 8.1.4 FIPS and Non-FIPS Modes 170
- 8.2.1 Key and Algorithm IDs 171
- 8.2.4 Encryption Key Select 173
- 8.2.5 Encryption Key Erase 173
- 8.3 Clear / Secure Strapping 174
- Override 175
- 8.4.2 Secure Call Behavior 175
- 8.7 Radio OTAR Capabilities 179
- 8.7.2 P25 Trunking Icons 180
- Data Features 181
- 9.2.1 Radio Configuration 182
- 9.2.2 Interface Connection 183
- 9.2.3 Context Activation 183
- 9.2.4 PPP Link Establishment 184
- (Figure 9.2) 185
- Tones & Error Messages 203
- 10.2 Error Messages 205
- Service Information 209
- 11.3 Factory Customer Service 210
- 11.4 Returns for Repairs 211
- 11.5 Replacement Parts 212
- 11.6 Internet Home Page 212
Produits connexes et manuels pour Les radios bidirectionnelles E.F. Johnson Company 5300 Series
(212 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.572 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels