E.F. Johnson Company 5300 Series Instructions d'exploitation Page 71
- Page / 216
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ES Series Mobile Radio Operating Manual 4-5
Radio Wide Features
Pressing the TX PWR switch toggles the power setting. The new level is flashed in the
display when this switch is pressed as “HI POWER” or “LOW POWER”. If selectable
power is not permitted on the current channel or system, the fixed power level is flashed
and no power change occurs. The selected power level is permanent until it is manually
changed again. The power levels are set at the factory or when the radio is tuned using the
PCTune™ software.
4.6 Alert Tone Select
The various alert tones that sound are described in Section 10.1. These tones can be
enabled and disabled if the TONE option switch is programmed. To turn all tones OFF,
press this switch and “TONE OFF” is displayed. Then to turn all tones on again, press it
and “TONE ON” is displayed. If this switch is not programmed, tones are fixed in the ON
or OFF condition by programming. Alert tones can be disabled depending on
programming.
The Alert Tone volume can be adjusted relative to the volume control setting. This is done
by programming and also by the user if the TN VOL option switch is programmed.
Relative levels of –170 to +170 can be set with “0” the default setting. A minus value
decreases the tone volume and a plus value increases it. The user adjusted level
permanently overrides the programmed level if applicable.
4.7 Power Turn-Off Delay
The radio can be installed so that the vehicle ignition switch as well as the front panel
power switch of the radio control power. This is done by connecting the accessory cable
ignition switch input to the vehicle ignition switch. Refer to the ES Series Mobile Radio
Installation Manual for more information. A power-off delay of up to 510 minutes can
then be programmed, or this feature can be disabled by programming “Infinite” delay so
that there is no automatic power-off.
Both the ignition switch and the power switch must then be on for radio power to turn on.
The delay can be overridden at any time by turning power OFF using the front panel
power switch or turning the ignition switch back ON.
This turn-off delay can allow calls to be received or the horn alert to be active for a time
after the ignition switch is turned OFF. At the same time, advantages of ignition switch
control are used such as preventing the battery discharge that may occur if the radio is left
ON for an extended period.
- ES Series Mobile Radio 1
- Operating Manual 1
- Table of Contents 5
- 3 General Operation 3-1 6
- 4 Radio Wide Features 4-1 7
- 7 Multi-Net Features 7-1 10
- Contents 11
- 9 Data Features 9-1 12
- 11 Service Information 11-1 12
- List of Figures 15
- List of Tables 17
- Safety Information 19
- Instructions 20
- Mobile Antennas 21
- Approved Accessories 22
- Radio Overview 23
- 1.3 Supported Software 25
- 1.4 Available Options 26
- 1.5 Licensing 27
- 1.6 Radio Accessories 27
- 1.6.2 Handheld Control Unit 28
- 1.6.3 Base Station Unit 29
- Controls & Display 31
- Programmable Option Buttons 32
- 2.1.2 Display 33
- 2.2 Lightning Control Head 36
- 2.2.1 Front Panel Controls 37
- *4-Way Navigation Pad 38
- 2.2.2 Display 39
- 2.2.3 Mobile Display Modes 40
- 2.3 Rear Panel Connectors 43
- 2.4.3 Hardware Setup 45
- 2.4.5 Dual Control Operation 47
- 2.5 External Speaker 48
- General Operation 51
- 3.1.1.1 Setting Volume Level 52
- 3.1.2 Power-Up Password 53
- 3.1.2.6 Master Password 54
- 3.1.2.7 Zone Password 54
- 3.1.6.1 Channel Lock Option 56
- 3.1.6.4 Direct Channel Select 57
- 3.1.7 Setting Squelch Control 59
- 3.1.8 Transmit Disable 60
- 3.1.12 Radio Service 61
- 3.2 Operating Modes 62
- 3.2.3 P25 Trunked Mode 63
- 3.2.4 Multi-Net Mode 64
- 3.2.5.1 Systems 65
- 3.2.5.2 Channels 66
- 3.2.5.3 Zones 66
- Radio Wide Features 67
- 4.2 Menu Mode 69
- 4.3 Time-Out Timer 70
- 4.4 Home Channel Select 70
- 4.5 Power Output Select 70
- 4.6 Alert Tone Select 71
- 4.7 Power Turn-Off Delay 71
- 4.8 Horn Alert 72
- 4.10 Surveillance Mode 73
- 4.11 Public Address 73
- 4.12 Scanning 74
- Scan Enable Indicator 75
- 4.13 Scan Lists 77
- Scan List Indicator 77
- 4.14.1 Viewing GPS Data 80
- 4.15 Over the Air Programming 81
- 4.15.2 OTAP Transfer Times 82
- 5.2 Monitor Mode 84
- 5.3 Busy Channel Lockout 85
- 5.4 Call Guard Squelch 85
- 5.4.2 Tone Call Guard Squelch 86
- 5.4.4 Disable Call Guard 87
- 5.5 Penalty Timer 88
- 5.6 Conversation Timer 89
- 5.7 Repeater Talk-Around 89
- 5.9 Emergency Alarm and Call 90
- 5.9.2 Emergency Call Alert 91
- 5.9.3 Emergency Calls 91
- 5.9.3.1 Emergency Hot Mic 92
- 5.9.5 Emergency Talkgroup 93
- 5.10.1 Selecting a Scan List 93
- Priority Indicator 95
- 5.10.4 Talkgroup Scanning 96
- 5.12 DTMF / ANI Signaling 98
- 5.12.1 Single Tone Encoder 99
- 5.12.2 Two Tone Encoder 99
- 5.12.3 Five Tone Encoder 100
- 5.12.4 MDC1200 Compatibility 100
- 5.12.5 GE Star 100
- 5.13 Project 25 Mode Features 101
- 5.13.6 P25 Group Calls 103
- 5.13.7 P25 Unit Calls 104
- 1 - 16 1 1 - 16 105
- 17 - 32 2 1 - 16 105
- 33 - 48 3 1 - 16 105
- 5.13.9 Call Alert 107
- 5.13.10 Call History 108
- 5.13.11 Messaging 108
- 5.13.12 Status Messaging 109
- 5.13.13 P25 Packet Data 109
- 5.14 Keypad Programming 110
- 5.14.2 Zone Password 111
- 5.14.3 Zone Change Parameter 112
- 5.14.5 System Parameters 112
- 5.14.6 Channel Parameters 113
- 5.15 Text Messaging 115
- Conventional Mode Features 118
- SMARTNET / SmartZone / P25 119
- Trunked Features 119
- 6.3 Standard Group Calls 120
- 6.5 Telephone Calls 125
- 6.6 Call Alert 127
- 6.6.1 Answering a Page 128
- 6.6.2 Initiating a Page 128
- 6.7 Messaging 130
- 6.8 Sending Status Conditions 130
- 6.9 Emergency Alarm and Call 131
- 6.9.2 Emergency Call Alert 132
- 6.9.3 Emergency Calls 132
- 6.10 Failsoft Operation 134
- 6.12 Dynamic Regrouping 137
- 6.13.1 Busy Override 138
- 6.13.2 Site Trunking 138
- 6.13.5 Auto Site Search 139
- 6.13.6 ZoneFail Site Lock 139
- 6.13.7 P25 Wide Area Scan 140
- 6.13.10 Radio Information 141
- Multi-Net Features 143
- 7.2 Multi-Net Features 145
- 7.2.2 Receive Priority Calls 146
- 7.2.3 Access Priority 147
- 7.2.4 System Authorization 147
- 7.3 Caller Identification 148
- 7.6 Emergency 149
- 7.7 Encryption 150
- 7.8 Group Scanning 150
- 7.8.2 Group Scan Lists 151
- 7.8.2.3 Scan List Select 152
- 7.8.3.1 Receive Delay 152
- 7.8.3.2 Call Delay 153
- 7.9 Multi-Net Group Calls 154
- 7.10 Multi-Net Special Calls 155
- CALL is 155
- 7.10.1 Placing A Special Call 156
- *, #, and 157
- 7.10.2.2 Directed Group Calls 158
- 7.12 Receive-Only Channels 161
- 7.13.1 Roaming (Site Search) 162
- 7.13.3 Automatic Site Search 162
- 7.13.5 Manual Site Search 163
- 7.14 Status Messages 164
- 7.15.1 Exiting Queue Mode 165
- 7.18 Transmit Inhibit 166
- 8.1 Encryption Algorithms 169
- 8.1.4 FIPS and Non-FIPS Modes 170
- 8.2.1 Key and Algorithm IDs 171
- 8.2.4 Encryption Key Select 173
- 8.2.5 Encryption Key Erase 173
- 8.3 Clear / Secure Strapping 174
- Override 175
- 8.4.2 Secure Call Behavior 175
- 8.7 Radio OTAR Capabilities 179
- 8.7.2 P25 Trunking Icons 180
- Data Features 181
- 9.2.1 Radio Configuration 182
- 9.2.2 Interface Connection 183
- 9.2.3 Context Activation 183
- 9.2.4 PPP Link Establishment 184
- (Figure 9.2) 185
- Tones & Error Messages 203
- 10.2 Error Messages 205
- Service Information 209
- 11.3 Factory Customer Service 210
- 11.4 Returns for Repairs 211
- 11.5 Replacement Parts 212
- 11.6 Internet Home Page 212
Produits connexes et manuels pour Les radios bidirectionnelles E.F. Johnson Company 5300 Series
(212 pages)TANDBERG Mise en réseau manuels d'utilisation
À partir de M
Commentaires sur ces manuels