E.F. Johnson Company 5300 Series Instructions d'exploitation Page 88
- Page / 216
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-6 ES Series Mobile Radio Operating Manual
Conventional Mode Features
When the Call Guard code is changed using this feature, it remains selected even if other
channels are selected. However, if radio power is cycled or a talk-around channel is
selected, the normal codes are reselected. When scanning, the selected code also applies to
all scanned channels. Each channel can also be programmed to always ignore the code
selected from this list and use the default code instead.
If both analog and digital (Project 25) channels can be selected or scanned, the CTCSS/
DCS code for the selected position is used for analog channels and the NAC code for the
selected position is used for P25 channels. If a channel is programmed for mixed mode
operation, the selective squelch type (analog or digital) programmed for the transmit mode
determines the selective squelch type used.
Note Call Guard codes may be permanently reprogrammed by keypad programming (see
Section 5.14).
Proceed as follows to select a code using the SQ LIST option switch:
1 Press the SQ LIST option switch and then rotate the Select switch to select the desired
position. The display indicates “SEL SQ xx” where, “xx” is the selected code from 1-
64. The code number and actual code are alternately displayed (NACs are displayed in
hexadecimal).
2 To select the displayed code and return to the normal display, press the SQ LIST
(Squelch Code Select) switch again.
3 To check which code is selected, press the SQ LIST option switch once to display the
current selection and then again to return to normal operation.
4 To return to the normal selective squelch codes, select “DEFAULT” in this mode. As
previously described, the normal codes are also automatically reselected whenever
radio power is cycled or a talk-around channel is selected.
5.5 Penalty Timer
A penalty timer may be programmed on conventional systems to prevent transmissions for
the programmed time after the time-out timer disables the transmitter (see Section 4.3).
The penalty timer can be programmed for the same times as the time-out timer, and timing
starts when the PTT switch is released. If the PTT switch is pressed while the timer is
running the timer stops, and continues when the PTT switch is released. When the penalty
timer expires, a beep sounds and the transmitter can then be keyed.
- ES Series Mobile Radio 1
- Operating Manual 1
- Table of Contents 5
- 3 General Operation 3-1 6
- 4 Radio Wide Features 4-1 7
- 7 Multi-Net Features 7-1 10
- Contents 11
- 9 Data Features 9-1 12
- 11 Service Information 11-1 12
- List of Figures 15
- List of Tables 17
- Safety Information 19
- Instructions 20
- Mobile Antennas 21
- Approved Accessories 22
- Radio Overview 23
- 1.3 Supported Software 25
- 1.4 Available Options 26
- 1.5 Licensing 27
- 1.6 Radio Accessories 27
- 1.6.2 Handheld Control Unit 28
- 1.6.3 Base Station Unit 29
- Controls & Display 31
- Programmable Option Buttons 32
- 2.1.2 Display 33
- 2.2 Lightning Control Head 36
- 2.2.1 Front Panel Controls 37
- *4-Way Navigation Pad 38
- 2.2.2 Display 39
- 2.2.3 Mobile Display Modes 40
- 2.3 Rear Panel Connectors 43
- 2.4.3 Hardware Setup 45
- 2.4.5 Dual Control Operation 47
- 2.5 External Speaker 48
- General Operation 51
- 3.1.1.1 Setting Volume Level 52
- 3.1.2 Power-Up Password 53
- 3.1.2.6 Master Password 54
- 3.1.2.7 Zone Password 54
- 3.1.6.1 Channel Lock Option 56
- 3.1.6.4 Direct Channel Select 57
- 3.1.7 Setting Squelch Control 59
- 3.1.8 Transmit Disable 60
- 3.1.12 Radio Service 61
- 3.2 Operating Modes 62
- 3.2.3 P25 Trunked Mode 63
- 3.2.4 Multi-Net Mode 64
- 3.2.5.1 Systems 65
- 3.2.5.2 Channels 66
- 3.2.5.3 Zones 66
- Radio Wide Features 67
- 4.2 Menu Mode 69
- 4.3 Time-Out Timer 70
- 4.4 Home Channel Select 70
- 4.5 Power Output Select 70
- 4.6 Alert Tone Select 71
- 4.7 Power Turn-Off Delay 71
- 4.8 Horn Alert 72
- 4.10 Surveillance Mode 73
- 4.11 Public Address 73
- 4.12 Scanning 74
- Scan Enable Indicator 75
- 4.13 Scan Lists 77
- Scan List Indicator 77
- 4.14.1 Viewing GPS Data 80
- 4.15 Over the Air Programming 81
- 4.15.2 OTAP Transfer Times 82
- 5.2 Monitor Mode 84
- 5.3 Busy Channel Lockout 85
- 5.4 Call Guard Squelch 85
- 5.4.2 Tone Call Guard Squelch 86
- 5.4.4 Disable Call Guard 87
- 5.5 Penalty Timer 88
- 5.6 Conversation Timer 89
- 5.7 Repeater Talk-Around 89
- 5.9 Emergency Alarm and Call 90
- 5.9.2 Emergency Call Alert 91
- 5.9.3 Emergency Calls 91
- 5.9.3.1 Emergency Hot Mic 92
- 5.9.5 Emergency Talkgroup 93
- 5.10.1 Selecting a Scan List 93
- Priority Indicator 95
- 5.10.4 Talkgroup Scanning 96
- 5.12 DTMF / ANI Signaling 98
- 5.12.1 Single Tone Encoder 99
- 5.12.2 Two Tone Encoder 99
- 5.12.3 Five Tone Encoder 100
- 5.12.4 MDC1200 Compatibility 100
- 5.12.5 GE Star 100
- 5.13 Project 25 Mode Features 101
- 5.13.6 P25 Group Calls 103
- 5.13.7 P25 Unit Calls 104
- 1 - 16 1 1 - 16 105
- 17 - 32 2 1 - 16 105
- 33 - 48 3 1 - 16 105
- 5.13.9 Call Alert 107
- 5.13.10 Call History 108
- 5.13.11 Messaging 108
- 5.13.12 Status Messaging 109
- 5.13.13 P25 Packet Data 109
- 5.14 Keypad Programming 110
- 5.14.2 Zone Password 111
- 5.14.3 Zone Change Parameter 112
- 5.14.5 System Parameters 112
- 5.14.6 Channel Parameters 113
- 5.15 Text Messaging 115
- Conventional Mode Features 118
- SMARTNET / SmartZone / P25 119
- Trunked Features 119
- 6.3 Standard Group Calls 120
- 6.5 Telephone Calls 125
- 6.6 Call Alert 127
- 6.6.1 Answering a Page 128
- 6.6.2 Initiating a Page 128
- 6.7 Messaging 130
- 6.8 Sending Status Conditions 130
- 6.9 Emergency Alarm and Call 131
- 6.9.2 Emergency Call Alert 132
- 6.9.3 Emergency Calls 132
- 6.10 Failsoft Operation 134
- 6.12 Dynamic Regrouping 137
- 6.13.1 Busy Override 138
- 6.13.2 Site Trunking 138
- 6.13.5 Auto Site Search 139
- 6.13.6 ZoneFail Site Lock 139
- 6.13.7 P25 Wide Area Scan 140
- 6.13.10 Radio Information 141
- Multi-Net Features 143
- 7.2 Multi-Net Features 145
- 7.2.2 Receive Priority Calls 146
- 7.2.3 Access Priority 147
- 7.2.4 System Authorization 147
- 7.3 Caller Identification 148
- 7.6 Emergency 149
- 7.7 Encryption 150
- 7.8 Group Scanning 150
- 7.8.2 Group Scan Lists 151
- 7.8.2.3 Scan List Select 152
- 7.8.3.1 Receive Delay 152
- 7.8.3.2 Call Delay 153
- 7.9 Multi-Net Group Calls 154
- 7.10 Multi-Net Special Calls 155
- CALL is 155
- 7.10.1 Placing A Special Call 156
- *, #, and 157
- 7.10.2.2 Directed Group Calls 158
- 7.12 Receive-Only Channels 161
- 7.13.1 Roaming (Site Search) 162
- 7.13.3 Automatic Site Search 162
- 7.13.5 Manual Site Search 163
- 7.14 Status Messages 164
- 7.15.1 Exiting Queue Mode 165
- 7.18 Transmit Inhibit 166
- 8.1 Encryption Algorithms 169
- 8.1.4 FIPS and Non-FIPS Modes 170
- 8.2.1 Key and Algorithm IDs 171
- 8.2.4 Encryption Key Select 173
- 8.2.5 Encryption Key Erase 173
- 8.3 Clear / Secure Strapping 174
- Override 175
- 8.4.2 Secure Call Behavior 175
- 8.7 Radio OTAR Capabilities 179
- 8.7.2 P25 Trunking Icons 180
- Data Features 181
- 9.2.1 Radio Configuration 182
- 9.2.2 Interface Connection 183
- 9.2.3 Context Activation 183
- 9.2.4 PPP Link Establishment 184
- (Figure 9.2) 185
- Tones & Error Messages 203
- 10.2 Error Messages 205
- Service Information 209
- 11.3 Factory Customer Service 210
- 11.4 Returns for Repairs 211
- 11.5 Replacement Parts 212
- 11.6 Internet Home Page 212
Produits connexes et manuels pour Les radios bidirectionnelles E.F. Johnson Company 5300 Series
(212 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.304 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels